+- Parsi Coders (http://parsicoders.com)
+-- انجمن: Web Development and Design (http://parsicoders.com/forumdisplay.php?fid=47)
+--- انجمن: PHP Forum (http://parsicoders.com/forumdisplay.php?fid=48)
+--- موضوع: سورس کد پرت اسکنر (پی اچ پی) (/showthread.php?tid=2454)
سورس کد پرت اسکنر (پی اچ پی) - Amin_Mansouri - 06-18-2012
کد:
<?
/*******************************************************************************
* Copyright 2002 - Adrian Ritchie :: GrinGod Productions :: aidy@gringod.com
*
* This software is being release by Adrian Ritchie for educational purposes.
* Whilst it may be re-used by other parties, the copy-right remains with
* Adrian Ritchie. Should this code be re-used either whole or in part, this
* agreement should be attached.
*
* Dislaimer:
* This software is for educational / private network use only. Do with it
* what you may, but on your own head be it!
*******************************************************************************/
class PortScanner {
var $start_ip; /* start of the ip range to scan */
var $stop_ip; /* end of the ip range to scan */
var $current_ip; /* current ip address being scanned (this is for future features) */
var $ports; /* array of ports to be scanned */
var $wait; /* how long to wait for a response from the port */
var $delay; /* how long to pause between each port */ /***
* Function PortScanner()
* Class constructor.
* Sets the start and end address of the scan range
* must be passed... but may be the same.
* The end address must be greater than the start address.
***/
function PortScanner($start, $stop) {
$this->start_ip = ip2long($start); /* store the start ip address as a long number */
$this->stop_ip = ip2long($stop); /* store the end ip address as a long number */
} /***
* Function set_ports
* Adds the passed ports to the array of ports to be scanned.
* This can either be a single port, a range of ports e.g. 1-90
* a a combination of both separated by commas (no spaces).
***/
function set_ports($ports) {
/* Explode ports into an array based on comma seperation.
Will create an array even if there is no comma so no need
to check for an array in following code */
$ports_array = explode(",",$ports); /* loop through array of ports */
foreach($ports_array as $key=>$val) {
/* try to explode port range into an array */
if(ereg("([0-9]+)\-([0-9]+)",$val, $buff)) {
/* loop through range to add each port */
for($ii=$buff[1]; $ii<=$buff[2]; $ii++) {
$this->ports[] = $ii;
}
} else {
/* only one port was sent so add that */
$this->ports[] = $val;
}
}
} /***
* Function set_wait
* Sets the time to wait for response from socket.
* Good object-oriented design doesn't allow access to class
* attributes, so accessor functions are provided.
***/
function set_wait($wait) {
$this->wait = $wait;
}
/***
* Function set_delay
* Sets the delay between each port check. Delay is in micro-seconds.
* Good object-oriented design doesn't allow access to class
* attributes, so accessor functions are provided.
***/
function set_delay($seconds=0, $microseconds=0) {
$this->delay = (1000000*$seconds) + $microseconds;
} /***
* Function do_scan
* Does the actual scan, based on the given details (see above functions).
***/
function do_scan() {
/* Loop through ip addresses.
This is why ip addresses are stored as long numbers as apposed
to Internet Protocol dotted addresses */
for($this->current_ip=$this->start_ip; $this->current_ip<=$this->stop_ip; $this->current_ip++) {
/* convert the long number back to a dotted address */
$ip = long2ip($this->current_ip);
/* loop through the ports and check each */
foreach($this->ports as $key=>$port) {
/* for unix systems, this will obtain the name of the service running
on that port. Win32 systems will just return N/A. */
if (!getservbyport($port,"tcp")) {$pname = "N/A";}
else {$pname = getservbyport($port,"tcp");}
/* attempt to open a socket to the port at the current ip address */
$ptcp = fsockopen($ip, $port, &$errno, &$errstr, $this->wait);
if($ptcp) {$status=1;} /* return 1 for open port (so users can display their own message */
else {$status=0;} /* return 0 for closed port (so users can display their own message */ /* return the results in a structured multi-dimensioned array
so the user can choose how to display the results */
$results["$ip"]["$port"]["pname"] = "$pname";
$results["$ip"]["$port"]["status"] = "$status"; /* start the delay before moving on to the next port */
$this->do_delay($this->delay);
}
} /* returnt the results to the user */
Return $results;
} /***
* Function do_delay
* This pauses execution for the passed length of time (micro-seconds)
* This allows a delay of less than 1 second for system which do not
* support usleep (Win32).
* This code was post on the PHP manual by "dsc at c2i dot net"
* I'm not sure if this works or not, so if your running *nix you
* may want to change this to use usleep();
***/
function do_delay($delay) {
$start = gettimeofday();
do{
$stop = gettimeofday();
$timePassed = 1000000 * ($stop['sec'] - $start['sec']) + $stop['usec'] - $start['usec'];
}while ($timePassed < $delay);
}
} /* get the target ip address */
$ip_address = gethostbyname("www.vbweb.co.uk"); /* set all the require atributes */
$my_scanner = new PortScanner($ip_address,$ip_address);
$my_scanner->set_ports("15-25,80,110,3306,1337,666");
$my_scanner->set_delay(1);
$my_scanner->set_wait(2); /* do the scan and capture the results */
$results = $my_scanner->do_scan();
/* display the results - this simply loops through the ip addresses and indents the results */
foreach($results as $ip=>$ip_results) {
echo gethostbyaddr($ip)."\n<blockquote>\n";
foreach($ip_results as $port=>$port_results) {
echo "\t".$port." : ".$port_results['pname']." : ";
if ($port_results['status']==1){echo "open";}else {echo "closed";}
echo "<br>\n";
}
echo "</blockquote>\n\n";
}
?>کد:
foreach($results as $ip=>$ip_results) {
echo gethostbyaddr($ip)."\n<blockquote>\n";
foreach($ip_results as $port=>$port_results) {
echo "\t".$port." : ".$port_results['pname']." : ";
if ($port_results['status']==1){echo "open";}
else {echo "closed";}echo "<br>\n";
}
echo "</blockquote>\n\n";
}